-
#160
by
Ronsmytheiii
on 17 May, 2010 15:47
-
Working caps and connectors, need to see if they can use higher torque, want words on a gap between boom and dish, but seems to be solid
-
#161
by
Chris Bergin
on 17 May, 2010 15:49
-
The Russians are talking over the loop, so we can't hear what's going on.
-
#162
by
Ronsmytheiii
on 17 May, 2010 15:56
-
sTill talking about gap between boom and dish, no fod in between, Tony suggests if it is secure, just put heat shield on
-
#163
by
Ronsmytheiii
on 17 May, 2010 15:58
-
want bravo 4 for bolts except 4, use alpha 7 for 4
-
#164
by
Ronsmytheiii
on 17 May, 2010 16:01
-
garrett cannot release the electrical cable, or close the bale, he is going to drive bolt 4 with alpha 7 on PGT
-
#165
by
Ronsmytheiii
on 17 May, 2010 16:05
-
-
#166
by
Ronsmytheiii
on 17 May, 2010 16:07
-
connector is open now, going to try to put it on again, still no joy
-
#167
by
Ronsmytheiii
on 17 May, 2010 16:09
-
still cant engage the bale waiting on the ground
-
#168
by
Ronsmytheiii
on 17 May, 2010 16:12
-
ground asking about metal shavings, small area where the connectors were rubbing, think need something else to put it on
-
#169
by
Ronsmytheiii
on 17 May, 2010 16:15
-
idea is to shield one end from sun and let the other get warm on the daylight side, then connect when sun comes up in 9 minutes
-
#170
by
Ronsmytheiii
on 17 May, 2010 16:17
-
-
#171
by
Ronsmytheiii
on 17 May, 2010 16:19
-
houston wants crew to close bale when not connected, goes all the way forward, when put it on this time push it down to help get soft sock
nothing
-
#172
by
Ronsmytheiii
on 17 May, 2010 16:22
-
tony wants to leave connector and go on to EOTP and let ground go back over it, Garrett wants to give one more big effort to get it on.
Going to cover one end to keep it cool while the other end is heated
-
#173
by
Ronsmytheiii
on 17 May, 2010 16:24
-
still worried about boom/antenna interface
-
#174
by
Ronsmytheiii
on 17 May, 2010 16:26
-
wohoo it worked! connector connected!
-
#175
by
Ronsmytheiii
on 17 May, 2010 16:28
-
talking about heat shield, going to gimbal locks, Garrett going off to EOTP, Steven is going to try the heat shield once.
-
#176
by
Ronsmytheiii
on 17 May, 2010 16:32
-
seems that Garrett is a multitasking, helped Steve while GCA ing Piers out
working on Gimabal locks
-
#177
by
Ronsmytheiii
on 17 May, 2010 16:34
-
Tony "Steve managed to get the heat shield done all by himself"
Swanny " We noticed that, he grew four hands"
-
#178
by
Ronsmytheiii
on 17 May, 2010 16:34
-
Steve has done two bolts on the gimbals lock, checking structural integrity, Steve says that it is pretty good, no wobble
-
#179
by
Ronsmytheiii
on 17 May, 2010 16:37
-
want to make sure interface is metal to metal