LIVE: STS-132 Flight Day 4 - EVA-1

• #140 by psloss on 17 May, 2010 15:14
• Quote from: Chris Bergin on 17 May, 2010 15:08

  Consumables: EV-2, O2, to 7:14.
  
  EVA-1 is on time, Steve a little ahead. Garrett a little behind.
  

  Talking limiting consumables; as Tony said, he doesn't want (the next EVAs) to have to go back to Z1.
  
  Second limiting one was LiOH for one of the EV crew at 7:56 PET.
  
• #141 by Chris Bergin on 17 May, 2010 15:14
• Asking what they should do.
  
  "You should enjoy being in space, on a spacewalk, with a camera and a view."
• #142 by psloss on 17 May, 2010 15:16
• Now talking "bingo" time -- need to start (Antenna Group Interface Tube / AGIT) heat shield task by 4:20 PET.  (Currently at 3:20.)
  
• #143 by Chris Bergin on 17 May, 2010 15:16
• Bingo time is to get to the heatshield by PET 4:20

  ---

  
• #144 by Chris Bergin on 17 May, 2010 15:17
• Great view

  ---

  
• #145 by psloss on 17 May, 2010 15:20
• Quote from: Chris Bergin on 17 May, 2010 15:17

  Great view
  

  Those stills should be spectacular.
  
• #146 by Chris Bergin on 17 May, 2010 15:20
• PGT action upcoming.

  ---

  

  
• #147 by Ronsmytheiii on 17 May, 2010 15:21
• Working on bolts on the SGANT boom

  ---

  

  
• #148 by Chris Bergin on 17 May, 2010 15:22
• I'm right next to the sun

  ---

  
• #149 by Chris Bergin on 17 May, 2010 15:25
• And that's 3:30 PET

  ---

  
• #150 by Ronsmytheiii on 17 May, 2010 15:27
• #151 by psloss on 17 May, 2010 15:28
• Quote from: Ronsmytheiii on 17 May, 2010 15:21

  Working on bolts on the SGANT boom
  

  For those following along in the EVA FDF, this is from 7-16; a step that could be done before getting into the dish steps.
  
  

  Quote

  CONNECT DISH CABLES TO BOOM
  75. Remove connector caps from boom J1 and J2
  
• #152 by Chris Bergin on 17 May, 2010 15:31
• Finite robotics, no Ku.
• #153 by psloss on 17 May, 2010 15:35
• GCA complete, Bowen working the bolts; here's his steps, also on 7-16:
  
  

  Quote

  INSTALL DISH ONTO BOOM
  70. GCA EV1 to install position
  71. Assist EV1 with fine alignment of dish
  72. Hand tighten bolt 1, wave guide bolt
  73. PGT[B1 (12.0), CW2] – 6-in ext-7/16: Drive bolts to hard
  stop; expect 8 turns
  .. Bolt 1 Torque: ______ Turns: ______
  .. Bolt 3 Torque: ______ Turns: ______
  .. Bolt 2 Torque: ______ Turns: ______
  
  
• #154 by Chris Bergin on 17 May, 2010 15:35
• Working on another bolt. Five turns.
• #155 by Chris Bergin on 17 May, 2010 15:38
• Might go back to Bolt 1 to get it torqued.
• #156 by Chris Bergin on 17 May, 2010 15:38
• Asked the retorque all three bolts, same settings as before.
• #157 by Chris Bergin on 17 May, 2010 15:41
• 10:39am Central for the bolting of the antenna.
• #158 by Chris Bergin on 17 May, 2010 15:41
• Dextre task up next.
• #159 by psloss on 17 May, 2010 15:44
• Garrett working on this section on 7-16:
  
  

  Quote

  40. Remove 6-in socket from PGT, stow in trash bag
  41. Receive ERAD from EV2, install on PGT
  .. Pull test
  42. PGT[A5 (7.0), CW2] – ERAD 2-in ext-7/16: Secure bolt 4;
  expect 4 turns at PGT
  Torque: ______ Turns: ______
  43. Stow PGT
  44. Release RET from Dish
  

  
  Just heard Tony calling out the PGT settings in step 42, expect slightly different number of turns.