-
#340
by
Ronsmytheiii
on 14 May, 2009 18:40
-
KU back at 2:12 pm CST (3:12 pm EST)
-
#341
by
Ronsmytheiii
on 14 May, 2009 18:41
-
Loosening did help, want to turn a few more times
-
#342
by
rocketguy101
on 14 May, 2009 18:41
-
Didn't they have issues with this door closing properly on the last repair mission?
-
#343
by
Ronsmytheiii
on 14 May, 2009 18:45
-
Go for a couple more turns, then try again
-
#344
by
Ronsmytheiii
on 14 May, 2009 18:46
-
going for two more
-
#345
by
Ronsmytheiii
on 14 May, 2009 18:47
-
does not think moving the bolt anymore will do anything, loose in bathtub. want to loosen handle bold
looks like we have TDRSS-Z
mark on telescope
-
#346
by
Ronsmytheiii
on 14 May, 2009 18:51
-
Does not want to engage the lever, should have lubed it
-
#347
by
Ronsmytheiii
on 14 May, 2009 18:55
-
hubble has been fighting all day today!:, trying to fit again
-
#348
by
Ronsmytheiii
on 14 May, 2009 18:57
-
Partial install for bottom before finishing the middle, still now seating
-
#349
by
Lawntonlookirs
on 14 May, 2009 18:57
-
What are the locks for that they are working on? No sound
-
#350
by
Ronsmytheiii
on 14 May, 2009 18:58
-
think that after loosening middle bolt bottom one tightened, so going to loosen it, it is tight again, go for full release on bottom bolt
-
#351
by
generic_handle_42
on 14 May, 2009 18:59
-
Atlantis will be moving into daylight momentarily.
-
#352
by
Ronsmytheiii
on 14 May, 2009 19:01
-
talking about the bottom bolt, drew want to do the bottom middle first, partial on the bottom another 10 minutes until payload bay cleanup
-
#353
by
I14R10
on 14 May, 2009 19:03
-
-
#354
by
Ronsmytheiii
on 14 May, 2009 19:03
-
full install on the bottom, skip middle, drew says he thinks he can do it in a few minutes so Houston says ok
-
#355
by
Ronsmytheiii
on 14 May, 2009 19:05
-
what to do with bolts? either locks or bolts
looking better, remove lock on lower middle, drew thinks like there is a high running torque, wants to throw handle but goign to stand down
-
#356
by
Ronsmytheiii
on 14 May, 2009 19:09
-
concern for clearances for lock may cause a gap, do not want to install lock, best effort to reinstall bolt.
No gaps, going to lower middle bolt to tighten
After doing bolt, want to lube it
-
#357
by
Ronsmytheiii
on 14 May, 2009 19:15
-
working on the pesky middle, PGT torqued out no turns
-
#358
by
Ronsmytheiii
on 14 May, 2009 19:18
-
finally turned, will not turn at any other setting, ASLR install now
-
#359
by
Ronsmytheiii
on 14 May, 2009 19:20
-
its a day of surprises